Puller Tool
Puller Tool
How hard is a Half shaft replacement? Can you give me a general break down?ANY special tools needed?
DO I NEED ANY SPECIAL PULLERS OR TOOLS TO PRESS FIT ANYTHING?
Most cars I figure are similar but I am doing half shafts on the front of two subarus. One an 82 and the other an 93.
What all has to be disconnected? Just a general break down I am waiting on a afctory manual. So just want to know a rough idea what to expect. Ball Joints,tie rods,suspension,hubs???
Also does a half shaft just slid out of the spline?
DO I NEED ANY SPECIAL PULLERS OR WAYS TO PRESS FIT ANYTHING?
Only special tool that jumps out is a ball joint separator, (looks like a tuning fork). Remove the lower ball joint key and nut, remove the axle nut then place the separator between the steering knuckle and the ball joint and smack it with a hammer. Once the ball joint is free, push down the lower control arm (you will probably have to loosen and remove the anti-roll tube connector if equipped). Remove the outer tie rod the same way, grab the knuckle and pull outwards and the axle should slip out of the hub assy. After that, the axle will usually slip out of the transaxle (sometimes you have to GENTLY pry the axle a little). STOP HERE. At this point you will be hundreds of hours and tens of dollars ahead to simply replace the ENTIRE axle shaft with a rebuilt unit. It goes together just like it came off vs having to disassemble the shaft, replace the orbiting bearings, grease, boots and joints. Your vehicle may not be that simple -- actually nothing on a Subie is as simple as say a Nissan Altima, i.e; brakes may have to be removed, etc. but the basic principal is the same. Always buy new cotter pins for reassembly!
 |
 17 PC SLIDE HAMMER PULLER TOOL SET NEW  US $73.95
|
 K Tool Slide Hammer Puller Kit KTI 70510 US $96.99
|
 Tool Aid Junior Slugger Slide Hammer Dent Puller US $32.99
|
 10 Way Slide Hammer Puller Set with Storage Case OTC7948 US $282.34
|
 Clamping Range 30 91mm Bearing Puller Disassembly Tool US $26.52
|
 K Tool 70356 PULLER PILOT BEARING SLIDE HAMMER US $48.95
|
 Norton Atlas Commando fork tube puller tool 650 750 850 US $35.50
|
 Wine Cork Puller Bottle Corkscrew Opener Red White Tool US $7.27
|
 3 TON LEVER BLOCK CHAIN HOIST PULLER RATCHET TYPE TOOL US $94.99
|
 SLIDE HAMMER WITH GEAR HUB PULLER AXLE DENT AXEL TOOL US $69.99
|
 Performance Tool Slide Hammer Puller Set Brand New US $89.99
|
 SGT 81500 S G Tool Aid Junior Slugger Slide Hammer Dent Puller US $40.18
|
 KEN TOOL T 500 H HUB PULLER US $49.99
|
 TA 81200 Tool Aid Midi Weight Slide Hammer Dent Puller US $59.95
|
 K D TOOL 2289 PITMAN ARM PULLER LOT EXCELLENT FREE SHIPPING USA MADE US $20.50
|
 VAUGHAN OCTAGON AXE HAMMER TOOL NAIL PULLER 3 1 2 IN CUT 26 OZ HAMMER US $9.99
|
 PDR PAINTLESS GLUE PULLER AUTO BODY TOOLS SLIDE HAMMER US $189.00
|
 Puller Set Slide Hammer Dent Pulling KDT2290 US $51.99
|
 Slide Hammer TBar Glue Puller PDR Tools Paintless Dent Repair Hail Removal US $129.00
|
| Powered by phpBay Pro |
Wheelchair Weed Twister-Puller: Adaptive Garden Tool -Test 4
Leave a Reply
You must be logged in to post a comment.